- Product category
-
Product name：ESD PA66 Plastic Compound
Product description：ESD A 280 FR
Nylon 6/6 (PA)
Carbon Fiber
Flame Retardant
ESD Plastic Compound
Static Dissipative
PROPERTIES & AVERAGE VALUES OF INJECTION MOLDED SPECIMENS
PERMANENCEEnglish SI Metric ASTM
TESTSpecific Gravity 1.45 1.45 D 792 Molding Shrinkage 1/8 in (3.2 mm) section 0.0020 - 0.0040 in/in 0.20 - 0.40 % D 955
MECHANICALImpact Strength, Izod notched 1/8 in (3.2 mm) section 1.2 ft-lbs/in 64 J/m D 256 unnotched 1/8 in (3.2 mm) section 8.0 ft-lbs/in 427 J/m D 4812 Tensile Strength 19000 psi 131 MPa D 638 Tensile Elongation 2.0 - 4.0 % 2.0 - 4.0 % D 638 Tensile Modulus 1.50 x 10^6 psi 10342 MPa D 638 Flexural Strength 29000 psi 200 MPa D 790 Flexural Modulus 1.20 x 10^6 psi 8274 MPa D 790
ELECTRICALVolume Resistivity 1000 - 9.9E+09 ohm.cm 1000 - 9.9E+09 ohm.cm D 257 Surface Resistivity 1.0E+5 - 9.9E+11 ohm/sq 1.0E+5 - 9.9E+11 ohm/sq D 257
ESD STM11.11Surface Resistance 1.0E+4 - 9.9E+10 ohm 1.0E+4 - 9.9E+10 ohm ESD STM11.11 Static Decay MIL-PRF-81705D, 5kV to 50 V, 12% RH < 2.00 s < 2.00 s FTMS101C
4046.1
THERMALIgnition Resistance* Flammability** V-0 @ 1/16 in V-0 @ 1.5 mm D 3801 PROPERTY NOTES Data herein is typical and not to be construed as specifications.
Unless otherwise specified, all data listed is for natural or black colored materials. Pigments can affect properties.* This rating is not intended to reflect hazards of this or any other material under actual fire conditions.
GENERAL PROCESSING FOR INJECTION MOLDINGEnglish SI Metric Injection Pressure 10000 - 18000 psi 69 - 124 MPa Melt Temperature 530 - 570 °F 277 - 299 °C Mold Temperature 150 - 225 °F 66 - 107 °C Drying 4 hrs @ 175 °F 4 hrs @ 79 °C Moisture Content 0.20 % 0.20 % Dew Point 0 °F -18 °C
PROCESSING NOTESDesiccant Type Dryer Required.
13 Nov 2007 LLM
This information is intended to be used only as a guideline for designers and processors of modified thermoplastics. Because design and processing is complex, a set solution will not solve all problems. Observation on a “trial and error” basis may be required to achieve desired results.
Data are obtained from specimens molded under carefully controlled conditions from representative samples of the compound described herein. Properties may be materially affected by molding techniques applied and by the size and shape of the item molded. No assurance can be implied that all molded articles will have the same properties as those listed.
Next：ESD PP Compound
