- 产品中心
- 联系我们
-
联系人:业务部 谭先生
手机号:18820179977
电话:0769-8326 7494
www.inchr.en.alibaba.com
www.inchrmaterial.com
-
产品名称:ESD C 380(RTP公司)
订购热线:18820179977(微信同号)
产品说明:
ESD C 380Polycarbonate (PC)Carbon FiberESD ProtectionElectrically Conductive
PROPERTIES & AVERAGE VALUES OF INJECTION MOLDED SPECIMENS
PERMANENCEEnglish
SI Metric
ASTM
TESTSpecific Gravity
1.25
1.25
D 792
Molding Shrinkage
1/8 in (3.2 mm) section
0.0010 - 0.0020 in/in
0.10 - 0.20 %
D 955
MECHANICALImpact Strength, Izod
notched 1/8 in (3.2 mm) section
1.7 ft-lbs/in
91 J/m
D 256
unnotched 1/8 in (3.2 mm) section
10.0 ft-lbs/in
534 J/m
D 4812
Tensile Strength
17500 psi
121 MPa
D 638
Tensile Elongation
2.0 - 3.0 %
2.0 - 3.0 %
D 638
Tensile Modulus
1.20 x 10^6 psi
8274 MPa
D 638
Flexural Strength
25000 psi
172 MPa
D 790
Flexural Modulus
1.10 x 10^6 psi
7584 MPa
D 790
ELECTRICALVolume Resistivity
< 1E3 ohm.cm
< 1E3 ohm.cm
D 257
Surface Resistivity
< 1E6 ohm/sq
< 1E6 ohm/sq
D 257
ESD STM11.11Surface Resistance
< 1E5 ohm
< 1E5 ohm
ESD STM11.11
Static Decay
MIL-PRF-81705D, 5kV to 50 V, 12% RH
< 2.00 s
< 2.00 s
FTMS101C
4046.1
THERMALDeflection Temperature
@ 264 psi (1820 kPa)
290 °F
143 °C
D 648
PROPERTY NOTES
Data herein is typical and not to be construed as specifications.
Unless otherwise specified, all data listed is for natural or black colored materials. Pigments can affect properties.
GENERAL PROCESSING FOR INJECTION MOLDINGEnglish
SI Metric
Injection Pressure
10000 - 15000 psi
69 - 103 MPa
Melt Temperature
550 - 600 °F
288 - 316 °C
Mold Temperature
180 - 250 °F
82 - 121 °C
Drying
4 hrs @ 250 °F
4 hrs @ 121 °C
Moisture Content
0.02 %
0.02 %
Dew Point
-20 °F
-29 °C
PROCESSING NOTESDesiccant Type Dryer Required.
2 Nov 2004 LCR
This information is intended to be used only as a guideline for designers and processors of modified thermoplastics. Because design and processing is complex, a set solution will not solve all problems. Observation on a “trial and error” basis may be required to achieve desired results.
Data are obtained from specimens molded under carefully controlled conditions from representative samples of the compound described herein. Properties may be materially affected by molding techniques applied and by the size and shape of the item molded. No assurance can be implied that all molded articles will have the same properties as those listed.
上一个产品:ESD C 380 FR(RTP公司)下一个产品:PPS